Cooktop Repair in Centennial, CO
Cooktop problems split by fuel and by zone: one zone out, heat stuck high, or ports that will not light. Most repairs run $100 to $500. The visit is $89, credited to the repair. Tell us the fuel type and which zone when you book, and the tech starts testing in the right place.
Frequently Asked Questions
How much does cooktop repair cost in Centennial?
Most repairs run $100 to $500. The visit is $89, credited to the repair. Elements and igniters run low; induction boards run high.
One zone is out. What failed?
The element is the top suspect, with its limiter and switch next. Each is tested in order at the visit.
Heat is stuck high on one zone. Why?
A failed limiter or switch that no longer cycles the element. Book it — a runaway zone can crack glass over time.
My induction top shows an error code. Help?
Note the code and test with a known magnetic pan first. If the code stays, the zone sensor or board is next, and the code speeds the visit.
Gas ports will not light on one burner. What now?
Clean the ports and reseat the cap dead-center. If it still clicks with no catch, the igniter is the next test.
What Does My Appliance Repair Cost?
Appliance repair is priced per job — by the part that failed, not by the hour. Here are the ranges we see on real jobs around Centennial, and a calculator built on the same numbers. The $89 service visit is credited to your repair when you go ahead.
Refrigerator & Freezer
Most refrigerator repairs land $200 to $300 — a fan motor, a defrost part, a control. The freezer circuit runs $200 to $400, and an ice maker runs $150 to $350. Sealed-system work — a compressor — is priced at the visit, never off a chart. The $89 visit fee is credited to the repair.
Washer & Dryer
A washer drain, pump, or belt repair runs $150 to $280; a motor or control runs $250 to $450. A dryer element or thermal part runs $100 to $250; a dryer motor or board runs $250 to $400. You get one price in writing before work starts.
Dishwasher
A pump, valve, or inlet repair runs $160 to $240; a motor or control runs $220 to $300. Standing water is usually a drain or pump problem — and the fix is quoted whole, parts and labor together, at the visit.
Oven, Stove & Cooktop
An igniter, element, or switch runs $150 to $300; a cooktop surface repair runs $100 to $300; a control board or gas valve runs $300 to $500. Gas work is tested for leaks before the tech leaves — every time.
Microwave
A door switch, fuse, or light repair runs $100 to $200; a magnetron or control runs $200 to $300. On an older countertop unit the honest answer is sometimes replacement — the tech will show you both numbers.
What Moves the Price
- The part. A defrost timer and a control board cost very different amounts. Every range here is keyed to the part class — and the written quote at the visit names the exact part before work starts.
- The $89 visit, credited. The service visit is $89 and it comes off the repair when you go ahead. If the fix is only the visit — a clogged filter, a tripped breaker — the $89 is the whole bill.
- Brand and age. Parts for some premium brands run higher and take a day or two to land. The quote says which, before you decide.
- Repair or replace. If a repair passes about half the cost of a comparable new appliance, the tech shows you both numbers. Sometimes the right call is a new machine — we would rather tell you that than sell a repair that will not hold.
These are planning ranges, not a quote — your final price is confirmed after an in-person look, before any work starts.
A note on parts. Most repairs here are figured with the part, the labor, and the credited $89 visit together. If a part has to be ordered, the quote says so up front with the day it lands — no open-ended waits, and the visit fee is never charged twice.
Estimate Your Repair
A compressor or sealed-system problem is priced at the visit — never off this chart. The $89 visit is credited to the repair.
Washer and dryer both down? Price the second one on the same visit here.
Standing water is usually the drain pump or a blocked line — quoted whole at the visit.
Gas lines are leak-tested before the tech leaves. The $89 visit is credited to the repair.
Built-in and over-range units price off this panel; countertop units get the honest repair-vs-replace math at the visit.
Free — no obligation. Your calculator numbers ride along with the request.
Send Your Repair to Centennial Expert Appliance Repair
Your estimate is attached automatically. Add your info and — if you can — a few photos of the appliance and its model label. Photos help us bring the right part the first time. Prefer to talk? Call (983) 900-5287.

One call, start to end
A Walnut Hills glass cooktop had one dead zone and one that ran all-or-nothing. Meter tests split the two problems: the element on one zone, the switch on the other. Both were fixed at one visit.
- Service performed
- Cooktop Repair.
- Scope of work
- Test the dead zone's element, switch, and sensor. Fit a new element. Test all zones.
- Materials / products used
- Radiant element.
- Size
- Glass-top radiant cooktop, four zones.
- Final price
- $248.
- Cost per sq ft
- Not applicable — appliance repair is priced per job, not per sq ft.
- Turnaround / duration
- Same day, about 1.5 hours on site.
- Payment terms / financing
- The $89 visit fee was credited to the repair. The rest was paid at the visit.
- Problem found
- One zone element open at the coil.
- Solution delivered
- New element fitted. The zone held a true simmer and a full boil on test.
- Homeowner first name
- Greg.
- Homeowner city / neighborhood
- Centennial — Walnut Hills.
- Homeowner situation (in their own terms)
- One zone died and one would not simmer — it was full blast or off. Weeknight cooking got old fast.
- Outcome and homeowner reaction
- Both problems fixed in one visit. Greg tested the simmer himself: 'Low means low again.'
Signs that point to this service
- A single zone or burner out
- Heat stuck high or cycling in a wild way
- Induction error codes, or a pan the top won't read
- Gas burners that won't light, or a poor flame shape
Not sure which one you have? Run the symptom check.
What usually causes it
Electric radiant and coil tops: elements, limiters, switches, and heat-worn wiring. Induction: zone sensors and power boards, plus the odd pan that isn't magnetic and only looks like a problem. Gas: ports blocked by boil-overs, igniters worn out, and caps out of place. Glass-top touch controls suffer most from steam and hard use.
Safe checks you can try first
Test induction zones with a known magnetic pan before you book — you may not need us. Reseat gas caps and clean the ports; half of all dead-igniter calls are cap placement. On coil tops, swap the dead coil with a live same-size one to tell an element problem from a socket problem.
Questions about cooktop repair
Need help in Centennial?
Call (983) 900-5287 or send the form. We'll tell you what the job needs and what it should cost before any work starts.
Request a repair visit
Related services: Refrigerator Repair, Washing Machine Repair, and Dryer Repair.
Also serving: Appliance Repair in Englewood, Appliance Repair in Centennial, and Appliance Repair in Greenwood Village.
Related Services
Refrigerator Repair · Freezer Repair · Ice Maker Repair · Washing Machine Repair · Dryer Repair · Dishwasher Repair · Oven Repair · Stove and Range Repair · Microwave Repair