Stove and Range Repair in Centennial, CO
A stove problem narrows fast once you name the fuel and the zone. Most repairs run $100 to $500. The visit is $89, credited to the repair. On electric tops we meter-test element, socket, and switch in order; on gas we test ports, igniters, and the spark module. The oven cavity itself sits on the oven repair page.
Frequently Asked Questions
How much does stove and range repair cost?
Most repairs run $100 to $500. The visit is $89, credited to the repair. Elements and igniters run low; glass zones and controls run high.
One burner is dead. What is it?
On electric: the element, its socket, or the switch. The swap test on the checks list splits them in a minute. On gas: ports or the igniter.
My burner is all or nothing — no simmer. Why?
The switch behind the knob, in most cases. It is a one-visit fix, tested across the full dial range.
Gas burners click and never catch. Help?
Clean ports and reseat caps first. If the click stays weak or one burner stays dead, the igniter or spark module is next.
A glass zone cycles off and stays off. What now?
That points at the element's temp limiter under the glass. Book it — the zone will not heal, and the limiter protects the glass.
What Does My Appliance Repair Cost?
Appliance repair is priced per job — by the part that failed, not by the hour. Here are the ranges we see on real jobs around Centennial, and a calculator built on the same numbers. The $89 service visit is credited to your repair when you go ahead.
Refrigerator & Freezer
Most refrigerator repairs land $200 to $300 — a fan motor, a defrost part, a control. The freezer circuit runs $200 to $400, and an ice maker runs $150 to $350. Sealed-system work — a compressor — is priced at the visit, never off a chart. The $89 visit fee is credited to the repair.
Washer & Dryer
A washer drain, pump, or belt repair runs $150 to $280; a motor or control runs $250 to $450. A dryer element or thermal part runs $100 to $250; a dryer motor or board runs $250 to $400. You get one price in writing before work starts.
Dishwasher
A pump, valve, or inlet repair runs $160 to $240; a motor or control runs $220 to $300. Standing water is usually a drain or pump problem — and the fix is quoted whole, parts and labor together, at the visit.
Oven, Stove & Cooktop
An igniter, element, or switch runs $150 to $300; a cooktop surface repair runs $100 to $300; a control board or gas valve runs $300 to $500. Gas work is tested for leaks before the tech leaves — every time.
Microwave
A door switch, fuse, or light repair runs $100 to $200; a magnetron or control runs $200 to $300. On an older countertop unit the honest answer is sometimes replacement — the tech will show you both numbers.
What Moves the Price
- The part. A defrost timer and a control board cost very different amounts. Every range here is keyed to the part class — and the written quote at the visit names the exact part before work starts.
- The $89 visit, credited. The service visit is $89 and it comes off the repair when you go ahead. If the fix is only the visit — a clogged filter, a tripped breaker — the $89 is the whole bill.
- Brand and age. Parts for some premium brands run higher and take a day or two to land. The quote says which, before you decide.
- Repair or replace. If a repair passes about half the cost of a comparable new appliance, the tech shows you both numbers. Sometimes the right call is a new machine — we would rather tell you that than sell a repair that will not hold.
These are planning ranges, not a quote — your final price is confirmed after an in-person look, before any work starts.
A note on parts. Most repairs here are figured with the part, the labor, and the credited $89 visit together. If a part has to be ordered, the quote says so up front with the day it lands — no open-ended waits, and the visit fee is never charged twice.
Estimate Your Repair
A compressor or sealed-system problem is priced at the visit — never off this chart. The $89 visit is credited to the repair.
Washer and dryer both down? Price the second one on the same visit here.
Standing water is usually the drain pump or a blocked line — quoted whole at the visit.
Gas lines are leak-tested before the tech leaves. The $89 visit is credited to the repair.
Built-in and over-range units price off this panel; countertop units get the honest repair-vs-replace math at the visit.
Free — no obligation. Your calculator numbers ride along with the request.
Send Your Repair to Centennial Expert Appliance Repair
Your estimate is attached automatically. Add your info and — if you can — a few photos of the appliance and its model label. Photos help us bring the right part the first time. Prefer to talk? Call (983) 900-5287.

One call, start to end
A Walnut Hills glass-top range lost its front zone and cycled wild on a second. Zone tests split the two problems: an open element and a worn limiter. Both went in at one visit.
- Service performed
- Stove and Range Repair.
- Scope of work
- Test each zone, swap a failed radiant element and its limiter, and test all zones hot.
- Materials / products used
- Radiant element, temp limiter.
- Size
- Glass-top range, four zones.
- Final price
- $312.
- Cost per sq ft
- Not applicable — appliance repair is priced per job, not per sq ft.
- Turnaround / duration
- Same day, about 2 hours on site.
- Payment terms / financing
- The $89 visit fee was credited to the repair. The rest was paid at the visit.
- Problem found
- Front zone element open. Limiter worn.
- Solution delivered
- New element and limiter fitted. All four zones cycled the way they should.
- Homeowner first name
- Alex.
- Homeowner city / neighborhood
- Centennial — Walnut Hills.
- Homeowner situation (in their own terms)
- The big front burner died the week we had family in. One working zone for six people was rough.
- Outcome and homeowner reaction
- All zones back the same day. Alex said the zone-by-zone test 'found the problem in ten minutes flat.'
Signs that point to this service
- One burner or zone fully dead
- Heat that is all or nothing — no simmer
- Gas burners that click with no catch
- A glass zone that cycles off and stays off
Not sure which one you have? Run the symptom check.
What usually causes it
On electric tops, elements burn out and their sockets corrode till contact comes and goes; the switch behind the knob is the top suspect when heat will not hold a simmer. On gas, burner ports clog with boil-overs, igniters wear out, and spark modules weaken. Glass zones fail at the element or its limiter under the surface.
Safe checks you can try first
On coil tops, swap the dead burner with a same-size live one: if the problem moves, it is the burner; if it stays, it is the socket or switch. On gas, reseat the burner caps and clean the ports — half of all dead-igniter calls are cap placement. Tell us the fuel and the zone when you book.
Questions about stove and range repair
Need help in Centennial?
Call (983) 900-5287 or send the form. We'll tell you what the job needs and what it should cost before any work starts.
Request a repair visit
Related Services
Refrigerator Repair · Freezer Repair · Ice Maker Repair · Washing Machine Repair · Dryer Repair · Dishwasher Repair · Oven Repair · Cooktop Repair · Microwave Repair