Washing Machine Repair in Centennial, CO
Few problems mess up a Centennial home faster than a dead washer: school clothes, work clothes, and a tub of standing water. Most repairs run $150 to $450. The visit is $89, credited to the repair. We test in a set order — drain path first, then drive parts, then the lock and controls — since one symptom can come from three parts.
Frequently Asked Questions
How much does washing machine repair cost in Centennial?
Most repairs run $150 to $450. The visit is $89, credited to the repair. Pumps and belts run low; boards run high. The price is set in writing first.
My washer will not drain. What now?
Check the pump filter first if yours is a front-loader. If the filter is clean or yours is a top-loader, the pump moves to the top of the list. Do not run more loads till it drains.
Why does my washer shake and walk?
Worn suspension rods or shocks, or a load that is far off balance. Rods are a one-visit fix in most cases.
The door is locked with clothes in it. Help?
Write down any error code, then book. Locks fail safe — locked — and the lock or its control is tested in the first visit.
Is it worth fixing an older washer?
For pumps, belts, locks, and hoses, yes in most homes. A failed board on a worn-out drum is where replacement makes sense, and we will say so plain.
What Does My Appliance Repair Cost?
Appliance repair is priced per job — by the part that failed, not by the hour. Here are the ranges we see on real jobs around Centennial, and a calculator built on the same numbers. The $89 service visit is credited to your repair when you go ahead.
Refrigerator & Freezer
Most refrigerator repairs land $200 to $300 — a fan motor, a defrost part, a control. The freezer circuit runs $200 to $400, and an ice maker runs $150 to $350. Sealed-system work — a compressor — is priced at the visit, never off a chart. The $89 visit fee is credited to the repair.
Washer & Dryer
A washer drain, pump, or belt repair runs $150 to $280; a motor or control runs $250 to $450. A dryer element or thermal part runs $100 to $250; a dryer motor or board runs $250 to $400. You get one price in writing before work starts.
Dishwasher
A pump, valve, or inlet repair runs $160 to $240; a motor or control runs $220 to $300. Standing water is usually a drain or pump problem — and the fix is quoted whole, parts and labor together, at the visit.
Oven, Stove & Cooktop
An igniter, element, or switch runs $150 to $300; a cooktop surface repair runs $100 to $300; a control board or gas valve runs $300 to $500. Gas work is tested for leaks before the tech leaves — every time.
Microwave
A door switch, fuse, or light repair runs $100 to $200; a magnetron or control runs $200 to $300. On an older countertop unit the honest answer is sometimes replacement — the tech will show you both numbers.
What Moves the Price
- The part. A defrost timer and a control board cost very different amounts. Every range here is keyed to the part class — and the written quote at the visit names the exact part before work starts.
- The $89 visit, credited. The service visit is $89 and it comes off the repair when you go ahead. If the fix is only the visit — a clogged filter, a tripped breaker — the $89 is the whole bill.
- Brand and age. Parts for some premium brands run higher and take a day or two to land. The quote says which, before you decide.
- Repair or replace. If a repair passes about half the cost of a comparable new appliance, the tech shows you both numbers. Sometimes the right call is a new machine — we would rather tell you that than sell a repair that will not hold.
These are planning ranges, not a quote — your final price is confirmed after an in-person look, before any work starts.
A note on parts. Most repairs here are figured with the part, the labor, and the credited $89 visit together. If a part has to be ordered, the quote says so up front with the day it lands — no open-ended waits, and the visit fee is never charged twice.
Estimate Your Repair
A compressor or sealed-system problem is priced at the visit — never off this chart. The $89 visit is credited to the repair.
Washer and dryer both down? Price the second one on the same visit here.
Standing water is usually the drain pump or a blocked line — quoted whole at the visit.
Gas lines are leak-tested before the tech leaves. The $89 visit is credited to the repair.
Built-in and over-range units price off this panel; countertop units get the honest repair-vs-replace math at the visit.
Free — no obligation. Your calculator numbers ride along with the request.
Send Your Repair to Centennial Expert Appliance Repair
Your estimate is attached automatically. Add your info and — if you can — a few photos of the appliance and its model label. Photos help us bring the right part the first time. Prefer to talk? Call (983) 900-5287.

One call, start to end
A Walnut Hills front-loader ended each cycle with a tub of water. The drain path was checked first: the pump filter was matted shut. It was cleared, the pump tested fine, and no part was sold.
- Service performed
- Washing Machine Repair.
- Scope of work
- Drain the tub by hand, clear the pump filter, test the pump, and run a full drain-and-spin.
- Materials / products used
- Pump filter cleaned. Pump tested fine, so we kept it.
- Size
- Front-load washer, family size.
- Final price
- $89.
- Cost per sq ft
- Not applicable — appliance repair is priced per job, not per sq ft.
- Turnaround / duration
- Same day, about 1 hour on site.
- Payment terms / financing
- The $89 visit fee was credited to the repair. The rest was paid at the visit.
- Problem found
- Pump filter matted with lint, coins, and a sock.
- Solution delivered
- Filter cleared. The pump tested good, so no part was sold.
- Homeowner first name
- Mike.
- Homeowner city / neighborhood
- Centennial — Walnut Hills.
- Homeowner situation (in their own terms)
- The washer quit with a tub of water and a week of school clothes in it. I braced for a pump bill.
- Outcome and homeowner reaction
- The machine drained the same visit for the visit fee alone. Mike kept the coin from the filter 'as the trophy.'
Signs that point to this service
- Standing water left in the tub
- No spin, or a spin that never gets up to speed
- Puddles under or behind the machine
- A cycle that stops with the door locked and a code up
Not sure which one you have? Run the symptom check.
What usually causes it
Drain pumps and hoses clogged with lint and small items lead the list. Then: worn belts and motor couplers, failed door locks and lid switches, inlet valves that weep or will not open, worn suspension rods, and control boards. On front-loaders, a torn door boot is the classic slow leak.
Safe checks you can try first
On front-load washers, empty the pump filter — it sits behind the small door at the bottom front. Put towels and a shallow pan down first; there will be water. Clear what you find, rinse the filter, and run a drain-and-spin. Note any error code before you unplug the machine, and tell us the code when you book.
Questions about washing machine repair
Need help in Centennial?
Call (983) 900-5287 or send the form. We'll tell you what the job needs and what it should cost before any work starts.
Request a repair visit
Related services: Dryer Repair, Dishwasher Repair, and Oven Repair.
Also serving: Appliance Repair in Englewood, Appliance Repair in Centennial, and Appliance Repair in Greenwood Village.
Related Services
Refrigerator Repair · Freezer Repair · Ice Maker Repair · Dryer Repair · Dishwasher Repair · Oven Repair · Stove and Range Repair · Cooktop Repair · Microwave Repair