Ice Maker Repair in Centennial, CO
Ice makers fail in a set order, and the unit itself is the last suspect, not the first. Most repairs run $150 to $350. The visit is $89, credited to the repair. We check freezer temp, the fill tube, the inlet valve, and the filter before anyone blames the maker.
Frequently Asked Questions
How much does ice maker repair cost in Centennial?
Most repairs run $150 to $350. The visit is $89, credited to the repair. Tubes and filters run low; valves sit in the middle.
Why did my ice slow to a few cubes?
A frozen fill tube or a weak valve, in most cases. Freezer temp is read first, since a warm box stops the cycle cold.
Cubes come out hollow or stuck as one lump. Why?
Low water flow — a clogged filter or a valve on its way out. Flow is tested before the maker itself is blamed.
There is a leak at the back of the fridge. Serious?
Book today and shut the supply valve if you can find it. Lines and valves leak slow, then fast. The floor under the fridge is the real cost if it runs.
Off-tasting ice — is that the maker?
Most often the filter or old ice that sat and took on food smells. Dump the bin, change the filter, and let one full cycle run before you book.
What Does My Appliance Repair Cost?
Appliance repair is priced per job — by the part that failed, not by the hour. Here are the ranges we see on real jobs around Centennial, and a calculator built on the same numbers. The $89 service visit is credited to your repair when you go ahead.
Refrigerator & Freezer
Most refrigerator repairs land $200 to $300 — a fan motor, a defrost part, a control. The freezer circuit runs $200 to $400, and an ice maker runs $150 to $350. Sealed-system work — a compressor — is priced at the visit, never off a chart. The $89 visit fee is credited to the repair.
Washer & Dryer
A washer drain, pump, or belt repair runs $150 to $280; a motor or control runs $250 to $450. A dryer element or thermal part runs $100 to $250; a dryer motor or board runs $250 to $400. You get one price in writing before work starts.
Dishwasher
A pump, valve, or inlet repair runs $160 to $240; a motor or control runs $220 to $300. Standing water is usually a drain or pump problem — and the fix is quoted whole, parts and labor together, at the visit.
Oven, Stove & Cooktop
An igniter, element, or switch runs $150 to $300; a cooktop surface repair runs $100 to $300; a control board or gas valve runs $300 to $500. Gas work is tested for leaks before the tech leaves — every time.
Microwave
A door switch, fuse, or light repair runs $100 to $200; a magnetron or control runs $200 to $300. On an older countertop unit the honest answer is sometimes replacement — the tech will show you both numbers.
What Moves the Price
- The part. A defrost timer and a control board cost very different amounts. Every range here is keyed to the part class — and the written quote at the visit names the exact part before work starts.
- The $89 visit, credited. The service visit is $89 and it comes off the repair when you go ahead. If the fix is only the visit — a clogged filter, a tripped breaker — the $89 is the whole bill.
- Brand and age. Parts for some premium brands run higher and take a day or two to land. The quote says which, before you decide.
- Repair or replace. If a repair passes about half the cost of a comparable new appliance, the tech shows you both numbers. Sometimes the right call is a new machine — we would rather tell you that than sell a repair that will not hold.
These are planning ranges, not a quote — your final price is confirmed after an in-person look, before any work starts.
A note on parts. Most repairs here are figured with the part, the labor, and the credited $89 visit together. If a part has to be ordered, the quote says so up front with the day it lands — no open-ended waits, and the visit fee is never charged twice.
Estimate Your Repair
A compressor or sealed-system problem is priced at the visit — never off this chart. The $89 visit is credited to the repair.
Washer and dryer both down? Price the second one on the same visit here.
Standing water is usually the drain pump or a blocked line — quoted whole at the visit.
Gas lines are leak-tested before the tech leaves. The $89 visit is credited to the repair.
Built-in and over-range units price off this panel; countertop units get the honest repair-vs-replace math at the visit.
Free — no obligation. Your calculator numbers ride along with the request.
Send Your Repair to Centennial Expert Appliance Repair
Your estimate is attached automatically. Add your info and — if you can — a few photos of the appliance and its model label. Photos help us bring the right part the first time. Prefer to talk? Call (983) 900-5287.

One call, start to end
A SouthGlenn ice maker slowed to a few cubes a day. Freezer temp read a true 0°F; the fill tube was frozen shut. It was thawed, the valve tested fine, and two cycles timed out full-size.
- Service performed
- Ice Maker Repair.
- Scope of work
- Check freezer temp, thaw a frozen fill tube, test the inlet valve, and time two full ice cycles.
- Materials / products used
- Fill tube thawed. Valve tested fine, so we kept it.
- Size
- In-fridge ice maker, standard unit.
- Final price
- $164.
- Cost per sq ft
- Not applicable — appliance repair is priced per job, not per sq ft.
- Turnaround / duration
- Same day, about 1 hour on site.
- Payment terms / financing
- The $89 visit fee was credited to the repair. The rest was paid at the visit.
- Problem found
- Fill tube frozen shut after a cold snap.
- Solution delivered
- Tube thawed and flow tested. Two full cycles timed and full-size.
- Homeowner first name
- Nina.
- Homeowner city / neighborhood
- Centennial — SouthGlenn.
- Homeowner situation (in their own terms)
- Ice slowed to a few cubes a day right before a house full of guests. I bought bagged ice twice.
- Outcome and homeowner reaction
- Full trays again within a day. Nina said the temp check first 'saved us a valve we did not need.'
Signs that point to this service
- Ice output down to a few cubes a day, or none
- Cubes small, hollow, or stuck as one lump
- Leaks at the back of the fridge or in the freezer
- Off-tasting or cloudy ice
Not sure which one you have? Run the symptom check.
What usually causes it
Frozen fill tubes top the list in winter. Then: inlet valves that weaken or stick, filters long past their change date, and kinked or split supply lines. A freezer drifting above 0°F slows or stops the cycle timer. Overflow and no-shutoff problems live in the maker's arm or sensor.
Safe checks you can try first
Check the shutoff arm or the on/off switch — it is the top free fix. Change the water filter if it has been six months or more. Read the freezer temp with a thermometer; the maker needs a true 0°F to cycle on time. Look behind the fridge for a kinked line if the unit was pushed back recently.
Questions about ice maker repair
Need help in Centennial?
Call (983) 900-5287 or send the form. We'll tell you what the job needs and what it should cost before any work starts.
Request a repair visit
Related services: Cooktop Repair, Refrigerator Repair, and Washing Machine Repair.
Also serving: Appliance Repair in Centennial, Appliance Repair in Greenwood Village, and Appliance Repair in Lone Tree.
Related Services
Refrigerator Repair · Freezer Repair · Washing Machine Repair · Dryer Repair · Dishwasher Repair · Oven Repair · Stove and Range Repair · Cooktop Repair · Microwave Repair